Draytek Vigor VigorAccess IVD Manuel d'utilisateur

VigorAccess IVD Quick Start Guide Version: 1.0 Date: 2007/05/08

Version: 1.0 Quick Start Guide for VigorAccess IVD 8 ] RReeffeerreennccee –– CCoommmmoonn UUssee CCoommmmaannddss ffoorr CCoonnffiigguurraattii

Version: 1.0 Quick Start Guide for VigorAccess 9Admin/network> route -a <TargetIP> <NetMask> <GatewayIP> Add a stat

Version: 1.0 Quick Start Guide for VigorAccess IVD 10S How to Upgrade Firmware Users can use the following commands to upgrade new firmware. Make sur

Version: 1.0 Quick Start Guide for VigorAccess 11PPaarrtt IIII:: Here provides some general and common commands used in IVD for user

Version: 1.0 Quick Start Guide for VigorAccess IVD 12S How to Change ADSL Line Rate Users can use the following command to change the ADSL Line Rate

Version: 1.0 Quick Start Guide for VigorAccess 13S How to Change VPI/VCI for Existing VCC Users can use the following command to change

Version: 1.0 Quick Start Guide for VigorAccess IVD 14S How to Setup Port VLAN ID (PVID) Users can use the following command to setup port VLAN ID. Th

Version: 1.0 Quick Start Guide for VigorAccess 15status enable $create filter rule map ifname all ruleid <id2> stageid 1 S How to

Version: 1.0 Quick Start Guide for VigorAccess IVD 16S How to Upgrade Full Image Remotely Users can use the following command to remotely upgrade ful

Version: 1.0 Quick Start Guide for VigorAccess 17S Wizard Commands In addition to the primitive commands described as above. Several wi

Version: 1.0 Quick Start Guide for VigorAccess IVD 18PPaarrtt IIIIII:: Here provides commands used in IVD for users to configure VoIP features.

Version: 1.0 Quick Start Guide for VigorAccess 19S How to Set SIP local port Setting - Help IVD/voip/sip> localport ? - Display the

Version: 1.0 Quick Start Guide for VigorAccess IVD 20S How to Set MGCP Local Port Setting - Display the setting IVD/voip/mgcp> localport -s - Edi

Version: 1.0 Quick Start Guide for VigorAccess 21S How to Set MGCP Wildcarded End Point ID Setting - Help IVD/voip/mgcp> wildrsip ?

Version: 1.0 Quick Start Guide for VigorAccess IVD 22S How to Set Codec Setting - Help IVD/voip/sip> codec ? - Display the setting IVD/voip/sip&

Version: 1.0 Quick Start Guide for VigorAccess 23S How to Set DTMF Relay Setting - Help IVD/voip/sip> dtmf_relay ? - Display the s

Version: 1.0 Quick Start Guide for VigorAccess IVD 24S How to Set Call Forwarding Setting - Help IVD/voip/sip> callforward ? - Display the settin

Version: 1.0 Quick Start Guide for VigorAccess 25(Default is 1~24 mapped to 1~ 24 port) Note - It is very important to provide Group f

Version: 1.0 Quick Start Guide for VigorAccess IVD 26Destination Assign an address of dialing destination. Ex: [email protected] Memo Users can add some d

Version: 1.0 Quick Start Guide for VigorAccess 27S How to Set Region Code for Tone Setting - Help IVD/voip/tone> region ? - Display

Version: 1.0 Quick Start Guide for VigorAccess 1 IIVVDD QQuuiicckk SSttaarrtt GGuuiiddee This quick start guide will provide basic co

Version: 1.0 Quick Start Guide for VigorAccess IVD 28S How to Set User Defined Busy Tone Setting - Help IVD/voip/tone/user_defined> busy ? - Disp

Version: 1.0 Quick Start Guide for VigorAccess 29S How to Set User Defined Congestion Tone Setting - Help IVD/voip/tone/user_defined>

Version: 1.0 Quick Start Guide for VigorAccess IVD 30S How to Set ToS Setting - Help IVD/voip/qos> tos ? - Display the setting IVD/voip/qos> t

Version: 1.0 Quick Start Guide for VigorAccess 31S How to Set Dialing Timeout Setting - Help IVD/voip/misc> dialing_timeout ? - Dis

Version: 1.0 Quick Start Guide for VigorAccess IVD 321: Manually input NAT IP address 2: Auto discover NAT IP address Manually Input NAT IP Address NA

Version: 1.0 Quick Start Guide for VigorAccess 33Remote RTP Port It shows the used port number of remote voice site. RTP Statistic It sh

Version: 1.0 Quick Start Guide for VigorAccess IVD 34S How to Set Allow List of Incoming Calls Setting - Help IVD/voip/sip/incallbarring> allow ?

Version: 1.0 Quick Start Guide for VigorAccess 35S How to Activate VoIP configuration - Help IVD/voip> config ? - To activate voip

Version: 1.0 Quick Start Guide for VigorAccess IVD 2 Y MMaannaaggeemmeenntt ffoorr IIVVDD If users want to configure or monitor the devices, there

Version: 1.0 Quick Start Guide for VigorAccess 3S How to Login to DSL Module for Managing IVD Slave Slave device have DSL/VoIP module

Version: 1.0 Quick Start Guide for VigorAccess IVD 4 S How to Check the Version Information To display the basic information of the controller insi

Version: 1.0 Quick Start Guide for VigorAccess 5CPSwVersion : A24-A-1GE-2.10.2.8 DPSwVersion : DP_B02_10_14_60_ip1000a Syste

Version: 1.0 Quick Start Guide for VigorAccess IVD 6 \ CCoonnffiigguurraattiioonn bbyy UUssiinngg TTeellnneett To use Telnet for managing Master/S

Version: 1.0 Quick Start Guide for VigorAccess 7S How to Set G5 and G6 as UPLINK Interface For the environment with available Fiber con